Chinese ∣ English∣ Japanese ∣ Home ∣ Sitemap
 
  關於高力 　∣ 　技術認證 　∣ 　事業部介紹 　∣ 　投資人園地 　∣ 　企業徵才 　∣ 　最新消息 　∣ 　聯絡我們 　∣ 　回首頁
  金屬製品事業部
 
クリーンルーム高負荷鋼製高架フロア
    ◆ 製品の特色
    ◆ 使用對象
    ◆ 試験報告
    ◆ 產品の規格
 

Brazing
    ◆ Brazing
 
Service
    ◆ Contact Us
 
產品の規格

Grating Panels (GP)
PDF Download
Perforated Panel (PP)
PDF Download
Solid Panel (SP)
PDF Download
Chemical Ni-Cr Plating Panel
Window  Panel (WP)
Panel + Conductive Vinyl
Note: If a criteria of CISCA, JIS, CNS, or RAL is required, the unit price will be affected.　　　　　
■ Solid Panels (CISCA)
Top　　
 
■ Solid Panels (JIS)
Top　　
■ Grating Panels (CISCA)
Top　　
■ Grating Panel (JIS )
Top　　
■ Steel Access Floor Specifications (CISCA)
(*) Note:
1. All loads applied on center point of panel via a 1 square inch indenter area. A 50 Kg preloading is default. Results above indicate center point
of panel permanent set after application of concentrated load shall be 2mm (0.01").
2. All loads to be applied anywhere on panel via a 1 square inch indenter area. A 50 Kg preloading is default. Permanent set after application of
load shall be 1 mm (0.005").
3. A concentrated load is applied at center of panel via a 1 square inch indenter area. A 50 Kg preloading is default. Result shows where
permanent fractures occurred.
4. Local and beam top surface deformation shall not exceed 0.02mm (0.0008"), both 10 pass test and 10,000 pass test uses a 6" x 2" wide
alathane wheel. Loading on top of the wheel is 500Kgs.
5.Drop Impact Loads: A (200 Lb) 91kg weight drops from 1ft (305 mm) hight via a 1 square inch area. Results above indicate less than 1mm
(0.005") deformation.
6. Fatigue Test: Results above indicate 1 million cycles of loading and unloading force applied on the center of a panel via indenter.
 
■ Steel Access Floor Specifications (CISCA)
(*) Note:
1. All loads applied on center point of panel via a φ50mm indenter area. A 50 Kg preloading is default. Results above indicate center point of
panel permanent set after application of concentrated load shall be 2mm (0.01").
2. All loads to be applied anywhere on panel via a φ50mm indenter area. A 50 Kg preloading is default. Permanent set after application of load
shall be 1 mm (0.005").
3. A concentrated load is applied at center of panel via a φ50mm indenter area. A 50 Kg preloading is default. Result shows where permanent
fractures occurred.
4. Local and beam top surface deformation shall not exceed 0.02mm (0.0008"), both 10 pass test and 10,000 pass test uses a 6" x 2" wide
alathane wheel. Loading on top of the wheel is 500Kgs.
5.Drop Impact Loads: A (200 Lb) 91kg weight drops from 1ft (305 mm) hight via a 1 square inch area. Results above indicate less than 1mm
(0.005") deformation.
6. Fatigue Test: Results above indicate 1 million cycles of loading and unloading force applied on the center of a panel via indenter.
 
Note: Kaori reserves all rights to modify download data and content shown in web site without prior notices.
 

高力熱處理工業股份有限公司

 

 桃園縣中壢市中壢工業區吉林北路5-2號　 No.5-2, Chi-Li North Road, Chung-Li Industrial District, Chung-Li City , Taiwan.
  Kaori Heat Treatment Co., Ltd. TEL：+886-3-4511567 　FAX：+886-3-4625297 　E-Mail：floor@kaori.com.tw 　 brazing@kaori.com.tw